Easily monitor temperatures or moisture from a distance for one or multiple assets with Brady’s low cost RFID Labels that do not require energy or maintenance. Brady can include sensors in your RFID labels that can be activated by manual or fixed scanners on demand or at pre-programmed intervals.

RFID Temperature Labels

RFID Temperature Labels enable wireless temperature reading and monitoring for a wide range of devices, equipment, machines, racks, cables, pipes and structures. The flexible, temperature sensing smart labels can be applied to almost any surface to support informed proactive decision making.

Why you should consider Brady’s RFID solution for temperature monitoring?

• Easily monitor temperatures: low cost temperature monitoring with passive, ISO 18000-6C and ISO14443 NFC interface, and ETSI compliant bandwidth RFID smart labels that do not require energy or maintenance. Labels are energised when needed by HF or UHF compliant readers.
• Applicable to all surfaces: available in a wide range of thin and flexible industrial grade label materials with a variety of adhesives to stay attached to smooth, rough, or powdered surfaces, and to flat or curved surfaces.
• Complete solution: includes RFID labels, label printer, label design software, RFID reader with hard- and software support.

Potential applications include environmental monitoring, material and equipment monitoring, cold chain monitoring, data centre monitoring, maintenance and safety data collection, and greenhouse monitoring.

RFID UHF moisture label

RFID UHF moisture label is a general-purpose moisture sensor that is designed to detect and measure moisture levels in the surrounding environment, and it works across a wide variety of materials, providing both good read distance and sensing performance. This label is suitable for use in outdoor, indoor and UV exposed environments.

• UHF moisture label for general applications such as construction, healthcare, retail, industry, supply chain and others. The antenna is designed for application on non-metal surfaces.
• Polyester tag face material, with chip bonded to aluminium antenna using anisotropic conductive film adhesive, suitable for thermal transfer printing, including RFID encoding.
• Labels are outside wound and 100% inspected, 500 good RFID labels per roll with bad tags marked.

Discover smart RFID solutions from Brady!

What’s in store for research and development around the world? From super-apps, through psychedelic medicines, to metaverse and sustainable technology, 2023 has something for everyone. Here, tax incentive and innovation management advisers, ABGi take a look…

Super-apps

Super-app is a mobile or web application that allows for integration of multiple online services within one digital ecosystem. The term super-app was first used to describe WeChat, the hugely popular Chinese all-encompassing mobile application. Think of it as a Swiss knife with a range of built in smaller tools (mini-apps) that you can use and customise for different tasks.

2023 will see an increased interest in super-app solutions among developers and end users. This is expected in particular in the ‘west’, where there’s still no equivalent to the Chinese pioneering app. Walmart is reportedly developing a super-app for its workforce in order to create a single, streamlined experience for its employees and managers by replacing multiple vendor-supplier applications. For better or worse, Elon Musk has recently announced plans for his own super-app. It is likely that “‘X’, the everything app”, will have something to do with his acquisition of Twitter.

Psychedelic Medicines

Mental health issues are increasingly prevalent in contemporary societies and conventional medicine appear to have reached its limits in addressing them. The coming year could see a revolution in pharmaceutical industry through engagement with drugs long associated with hippy and party cultures. MDMA, Ketamine and Magic Mushrooms are currently in final stages of testing trials to treat various mental health conditions.

It is hoped that MDMA could be used in treatment of post-traumatic stress disorder. Ketamine is being tested to treat addiction related illnesses such as alcoholism. Finally, an active component of Magic Mushrooms – psilocybin – could be used for treatment-resistant cases of depression. Many researchers are hoping that 2023 will see first psychedelic-assisted therapies approved by regulatory bodies in the USA and the UK. It is likely that in the near future currently illegal substances might be prescribed to you by a doctor.

Metaverse

While it might have been recently popularised by Mark Zuckerberg, metaverse is much more than Facebook’s attempt to remain relevant. In a nutshell, metaverse allows people to replicate or even enhance their physical activities in a virtual reality world facilitated by headsets and smart glasses. The technology has been simmering under the global tech surface for a while but many industry specialists predict this year will be pivotal for both the users and developers. As the technology is increasingly becoming part of the public consciousness, we will be seeing more people joining in the fun with big brands hoping to start capitalising on their initial investments in various metaverses. 2023 will also see many smaller and mid-size businesses flocking to the virtual world to start new ventures and services.

Sustainable Technology

Driven by climate emergency and the war in Ukraine, the shift towards green and renewable solutions will only accelerate in 2023. Sustainable technology is a framework for digital solutions that can enable environmental, social and governance outcomes for businesses and customers. The framework adheres to circular economy principles by considering the environmental impacts throughout the entire life span of each product. It is expected that sustainable technology will not only incorporate well-established products but also create new avenues for tech development. In doing so the framework will also provide products and services that enable customers to meet their own sustainability goals.

Snickers Workwear’s Kneeguard™ is a world-leading, fully certified, trademarked system for knee protection against kneeling injuries and everyday knocks at work.

The combination of Kneeguard™ pads and the Kneeguard PRO positioning system in Snickers workwear trousers is a crucial combination for reliable knee protection. 

In Snickers Workwear trousers kneepad pockets, you can adjust the kneepads to different heights to ensure correct positioning -for you - for maximum protection. There’s also different types of Kneepads to fit different types of trousers to suit different jobs on site. 

Such as the specialist kneepads for the Floorlayer trousers and the slim-fit Kneepads specially for the slim-fit trousers.

The unique design features also make the kneepads extremely flexible when you walk, yet they close around your knees when you kneel down – without your knees sliding off when you move around.

With superb impact protection, themarket-leadingD30® Ergo kneepads are made of a unique material that moulds around your knee to provide enhanced impact protection and are great for tradesmen and women who spend a lot of time working on their knees.

Getting more information on the Snickers Workwear clothing range is easy. You can call the Helpline on 01484 854788; check out www.snickersworkwear.co.ukand download a digital catalogue or email This email address is being protected from spambots. You need JavaScript enabled to view it.

Snickers Workwear’s Kneeguard™ is a world-leading, fully certified, trademarked system for knee protection against kneeling injuries and everyday knocks at work.

The combination of Kneeguard™ pads and the Kneeguard PRO positioning system in Snickers workwear trousers is a crucial combination for reliable knee protection.

In Snickers Workwear trousers kneepad pockets, you can adjust the kneepads to different heights to ensure correct positioning - for you - for maximum protection. There’s also different types of Kneepads to fit different types of trousers to suit different jobs on site.

Such as the specialist kneepads for the Floorlayer trousers and the slim-fit Kneepads specially for the slim-fit trousers.

The unique design features also make the kneepads extremely flexible when you walk, yet they close around your knees when you kneel down – without your knees sliding off when you move around.

With superb impact protection, the market-leading D30® Ergo kneepads are made of a unique material that moulds around your knee to provide enhanced impact protection and are great for tradesmen and women who spend a lot of time working on their knees.

Getting more information on the Snickers Workwear clothing range is easy. You can call the Helpline on 01484 854788; check out www.snickersworkwear.co.uk and download a digital catalogue or email This email address is being protected from spambots. You need JavaScript enabled to view it.

This article can also be found in the article below.

International provider of surface protection solutions, Integrated Global Services (IGS), has announced an exclusive long-term distribution partnership with industrial instruments and services company Iberfluid Instruments, that will increase the availability of IGS services across Spain and Portugal.

Under the new partnership, Iberfluid Instruments, with offices in Madrid, Barcelona, Bilbao, Seville, and Lisbon, will distribute the full portfolio of IGS solutions to the Spanish and Portuguese markets.

The solutions that will be offered include HVTS, a proprietary on-site thermal spray solution to stop corrosion and erosion, the Hot-tek portfolio of online maintenance solutions, and Cetek ceramic coatings and Tube Tech fouling removal solutions, both of which improve heat transfer efficiency and reduce emissions in fired heaters.

Colin Bateman, Director of Business Development EMEA at IGS, said: “Spain and Portugal remain important markets for IGS in Europe. This new distribution partnership represents a strong commitment from both organizations to provide tailored solutions for clients in this territory that deliver proven ROI and improve process efficiencies and asset integrity.

“Iberfluid’s expertise and legacy across Spain and Portugal are undisputed and we are excited to work alongside them to leverage the availability of our solutions in this market. The partnership will allow IGS to increase its reach through Iberfluid’s five hubs in the region whilst nurturing its strong relationships and technical capabilities across a range of industries and applications.”

Gerard Morales, General Manager at Iberfluid Instruments, commented: “Iberfluid has more than 50 years of experience in supplying instruments and services for the measurement and control of industrial processes. We are confident that our distribution agreement with IGS, which offers world-class surface protection solutions, will continue to enhance our reputation and capabilities across Spain and Portugal. “

“We are looking forward to working with the local IGS teams to deliver excellent solutions and the very best customer service for clients and to expand our offering to better serve the requirements of the local market.”

Headquartered in Virginia, U.S., Integrated Global Services (IGS) is an international provider of surface protection solutions. It runs operational hubs, subsidiaries, and sales offices around the world, and has more than 35 years of experience helping customers solve metal wastage and reliability problems in mission-critical equipment.

Founded in 1972, Iberfluid Instruments provides turn-key services which cover the entire project cycle: from the planning and design of facilities, the start-up and maintenance of equipment, acceptance tests, calibrations, and other services that contribute to improving productivity and safety across heavy industry facilities.

For more information about IGS, visit: www.integratedglobal.com

For more information about Iberfluid Instruments, visit: www.iberfluid.com

In Winfield, Kansas they know a thing or two about energy. Since 1904, it has been a Pubic Power Community. Its residents are stockholders, with profits going to support vital city services such as police, fire, streets, and parks.

At the local wastewater facility, Clint Gregor also knows a thing or two about the treatment plant. He’s worked there since it was commissioned in 1996.

“We’re a top three power user here,” says Clint. “Energy takes up thirty percent of our budget, and in today’s world, we have to look at power consumption more than ever”.

While energy costs are firmly in the industry spotlight, Clint’s driving factor for continuous improvement at Winfield is total cost of ownership. Return on investment has been in focus of late over due to the prohibitive costs of maintaining some of their mixers.

The 1.5MGD plant serves a population of 12,000. A 7.5HP direct drive mixer in a 26-feet deep tank continued to have issues, causing unwanted downtime. Repair bills were somewhat of a shock.

“Being quoted around $8,000 to repair a mixer that cost $10,000 gets your attention,” added Clint. “We did everything we could to keep it going, but eventually it was all chewed up beyond repair. The costs of having the copper rewound on a direct drive mixer or replacing an impeller seem sky-high, with it seems everything geared to make the mixer almost a throwaway piece of equipment. This can’t be right. The work couldn’t be undertaken by a local repair shop, which adds to our costs, and then we were given lead times of anything between 18 and 20 weeks, which is totally unacceptable”.

Keen to find an alternative mixer that would not only give the best value in total cost of ownership, but also be energy efficient, Clint found help from local supplier, Fluid Equipment, for whom Jeff Ubben recommended a Landia mixer that he said would give a good 20-plus years of reliable service.

‘Not all mixers are the same’

“It was a very different, but far better construction compared to what we had”, continued Clint. “The mixer that failed also had a 16-pole motor, but the new one from Landia was just a 4-pole, which would be much better for controlling speeds. These were just the first signs, that despite what some people say in the industry, not all mixers are the same”.

Although it has a much lower rpm and considerably less horse power than the previous mixer, Clint reports that the Landia mixer provides just as good mixing, if not better. Additionally, the existing guide rail could be utilized, so installation was also easy and extremely cost-effective.

“Direct drive mixers have their place” commented Clint,” but with such a high content of internal copper for the size of the stator, this had also become a factor in their excessive weight for servicing. The Landia propellers are sturdier and therefore heavier, but overall, without all that copper, the Landia mixer is far lighter and easy to service, with a motor that is almost half the size of the failed unit”.

*

The City of Winfield was established in 1870 by the American military commander and political candidate, Winfield Scott (1786-1866). Known as ‘Old Fuss and Feathers’ for his insistence on proper military etiquette, he was also called ‘the Grand Old Man of the Army’ for his many years of service. That adherence to high standards and commitment to the job certainly seems to prevail in modern day Winfield. Clint and his team work tirelessly to meet ever stricter permit requirements (prescribed by the Environmental Protection Agency and the Kansas Department of Health and Environment) to protect the Walnut River, which was declared an outstanding national resource water in the late 1990's.

‘This mixer will soon pay for itself’

One year on, and persistence in best practice is paying off for Winfield with the Landia mixer using half the energy of its predecessor.

“I’ll say it again” concluded Clint, “total cost of ownership is best. This mixer will soon pay for itself. We also know that because of the way it is designed and the way the company behind it operates, we won’t be held to ransom for heavy repair bills and very expensive replacement parts. The amp draw is less than half of the old direct drive mixer, so we were confident of making significant energy savings, just as we are in its longevity – so much so, that in our adjacent tank we have another mixer that is coming to the end of its days – and when it needs to go, we’ll be replacing it with a Landia mixer”.

www.landiaworld.com

Figure 1: André van der Graaf, Product Manager, Perspect Benelux, outside the new SuperWrapII Training Centre

Belzona, global manufacturer of polymeric repair and protection materials, has opened its fifth SuperWrap II Training Centre on the European continent in partnership withits Dutch Distributor, Perspect Benelux.

Belzona SuperWrap II is a composite pipe and tank repair system, primarily used on damaged pipes and tank walls for a fast return-to-service. The system comprises of a fluid-grade epoxy resin, a reinforcement sheet based on fibre glass and carbon fibre, and a release film to consolidate repairs.

The pipe repair kit is available in three enhanced resins for application at different service temperatures, meaning that the solution can withstand temperatures between -60°C (-76 °F) and 150°C (302°F) once cured.

 Figures 2 & 3: Before (left) and after (right) images of Belzona SuperWrap II being used to restore strength to corroded pipe walls

André van der Graaf, Product Manager at Perspect Benelux,responsible for training at the facility, said: “After an intensive course at Belzona’s training facility in Harrogate, I’m glad to share my knowledge on how to apply the Belzona SuperWrap II system as a fully certified trainer. We are working very hard to optimise our facility in Dordrecht, Netherlands, to receive interested parties on how to apply Belzona SuperWrap II incertified conditions.”

Perspect Benelux has obtained a wealth of experience inproviding for its customers in areas such as pipe repair and tank linings. The opening of the new certified Belzona SuperWrap II Training Centre will enable the Company to share its expertise with project leaders and maintenance colleagues.

In addition to the new centre in the Netherlands, SuperWrap II Supervisor and Installer Training is available in the European region at Beltech Solutions AS (Norway), Alliatech (France), Rodator (Spain) and B.S. Italia (Italy). An extensive range of courses is also offered at Belzona’s Corporate Headquarters in Harrogate (UK), Miami (USA), Ontario (Canada), Chonburi (Thailand) and Nanjing (China), ensuring consistently highapplication standards for Belzona solutions across the globe.

Meanwhile, Belzona recently opened its first training facility on African soil at AESSEAL, South Africa, ensuring that its Contractors can access a first class standard of training no matter where they are based.

Ian Wade, Belzona’s Technical Services Manager, said: “The opening of Belzona’s SuperWrap II Training Centres, which are an extension of Belzona Corporate training, will help ensure that Installer and Supervisor training is available in the region to ultimately grow the Belzona SuperWrap II systemwhile offering high end training and technical support.”

Since 2021, training standards are upheld by the Belzona Corporate SuperWrap II Trainer Committee which audits trainers and facilities, as well as internal staff, every two years to renew their SuperWrap accreditations.

All SuperWrap training is also carried out in line with ISO 24817 and ASME PCC-2, ensuring that applications are taught to industry recognised engineering standards, while the courses can be delivered in either English or the respective native language of each Centre to maximise accessibility.

Belzona’s Application and Training Programme promotes safe and successful applications of its products, building on over 70 years of experience by minimising failures and continuing to demonstrate innovation and expertise in industrial polymeric coatings.

For more information about Belzona’s Application and Training Programme, please click here: https://www.belzona.com/en/about/training.aspx

This article can alos be found in the issue below.

Trelleborg Sealing Solutions exhibits its technical solutions in elastomers, high-performance plastics and composite materials at Global Industry 2023 in Lyon, France, from March 7 to 10, 2023.

Located in Hall 9 on stand 3A108, attendees can experience Trelleborg’s innovative technologies including high precision micromolded components; multicomponent technology which creates a single component from multiple assembled parts; and a wide range of Isolast^® Perfluoroelastomer (FFKM) materials. These are specifically engineered to meet demanding performance requirements including high temperatures and the presence of aggressive chemicals.

Also featured are Trelleborg’s HiSpin^® high-speed rotary seals designed to enhance the performance of the next-generation axles of electric vehicles, which are set to make up 30% of all traffic by 2030; FoodPro^® E75F1, a specially engineered material for universal use in food and beverage applications, which meets all global standards for food contact materials, and Advanced Composite Materials, custom-designed and manufactured to produce parts for a wide variety of applications.

Frederic Vitrat, Managing Director of Trelleborg Sealing Solutions France, says: "As a world leader in polymer solutions for sealing, damping and protecting critical applications in demanding environments, we provide customers with innovative solutions that accelerate their performance in a sustainable way. We work in partnership with our customers from the initial design concept to the development of the right solution for their application, enabling them to reduce time to market and adding value to processes and products.”

Pierre-Jean Guiho, Trelleborg Business Development Manager, adds: “Our unique digital tools allow us to share our in-depth knowledge and experience with engineers developing new systems or optimizing existing production equipment across a wide range of industries. Our five-step process includes specification, testing, optimization, validation and manufacturing, with specific tools created for each stage. This allows a customer to involve us at each phase of product development or equipment improvement.”

Trelleborg’s technical experts Jean-Philippe Perot, Pierre-Jean Guiho, Emmanuel Louison, Antoine Charrier, Eric Mary, Loïc Favre and Naren Sampath will be on hand to provide attendees with advice and expertise in sealing technologies, development and manufacturing.

For more information on Trelleborg’s latest innovations, go to: https://www.trelleborg.com/en/seals/products-and-solutions/latest-innovations

This article can also be found in the issue below.

Easy modular construction and environmentally safer than existing stressing systems

The Enerpac RP70A lightweight rail stressing kit for railway maintenance crews that is easier to transport and assemble and up to three times lighter than similar tools, is now Network Rail approved. The RP-70A hydraulic rail stressor and Enerpac ZC3-Series battery powered stressing pump provide a cordless, zero emission, rail stressor kit for rail track thermite welding.

Traditional fully assembled rail pullers are too heavy for operators to comfortably transport and deploy safely and quickly. The RP70A stressor uses modular components that can be assembled and installed on site without the need for tools, making preparation for rail stressing easier and safer. Assembly typically takes less than 2 minutes.

National Rail Registration

Registered with UK National Rail under Certificate of Acceptance PA05/06958, the Enerpac rail stressing kit is designed for railway maintenance crews who assemble and install the rail puller directly on site when adjusting the gap between rail ends for rail stressing, rail welding, repairing rail failures and servicing insulators. The durable, easy-to-assemble components, where each component is either a one or two man lift, including ZC3-Series pump and hose set, are up to three times lighter than similar tools. The complete kit can be transported in an optional specially designed steel transport frame.

The Enerpac RP70A stressor has a 70-ton pulling and 35-ton pushing capacity while holding the rail in neutral length during the thermite welding process. It uses aluminium, double-acting hydraulic cylinders enclosed within steel sleeves to protect the cylinder rods from damage, particularly weld splatter. For ease of handling and lifting, the RP70A includes certified lifting eyes.

The stressor is interchangeable with a range of powerpacks and is compatible with the cordless Enerpac ZC3-Series battery powered pump for a complete clean energy solution. This is especially useful when conducting rail stressing in tunnels and other enclosed spaces.

“For rail maintenance engineers faced with track that’s inaccessible without the cost and delay of using a crane to install a fully assembled rail puller, the Enerpac RP70A is the perfect solution,” says Patrick Frencken, Key Account Manager North West Europe, Enerpac. “What’s more, when used in combination with an Enerpac ZC3-Series battery powered pump you have a far greener and safer operation compared with a gas/petro-powered hydraulic pump.”

To learn more about the latest Enerpac tools, visit the Enerpac Innovations page on www.enerpac.com.

With some 20 projects completed in Hong Kong, Hart Door Systems arranged a visit to its head office and its production facility in Newcastle upon Tyne for staff from its Hong Kong distributor, AUB, which provides door access solutions for commercial, institutional and residential projects in south east China, in particular Hong Kong and Macau.

Hart’s export manager, John Loftus, says AUB’s experienced team’s in-depth market knowledge and product know-how “has been invaluable in the development of this part of the Far East as an important export destination for Hart”.

With Hart’s continuing development of new products “we felt it was timely to host a visit to Newcastle to learn more about Hart and its products,” says Mr Loftus.

He adds: “Hong Kong is a very interesting location given the extreme climate challenges and the restricted land availability which means many buildings have to be high-rise. As an example we recently completed the installation of Typhoon resistant shutters on an 18 storey building.”

Typical Hart products include its Terror Screen LPS1175 SR rated shutters for high security and its  Typhoon-grade roller shutter which withstands the extreme weather conditions. Examples of successful Hart contracts include 21 typhoon resistant shutters for the Terminal 1 Remote Transfer Facility and Midfield Baggage Hall for Hong Kong International Airport.

“Further orders include steel shutters for the Hong Kong Central Government and for the Hong Kong Palace Museum, the HK$3.5 billion replica of the capital’s celebrated Palace Museum at the West Kowloon Cultural District which opened last year,” adds Mr Loftus.

“By giving consultancy, design, manufacture, shipping and offering installation and maintenance training from a single source, Hart Doors simplifies project management and helps customers like AUB to feel confident in their industrial door purchase wherever they are in the World. 

“To be able to offer knowledge, advice and cradle to grave support is crucial when working on export projects.”

This article can alo be found in the issue below.